SKYRC 6x80 Plus is a high-performance, micro processor control
charge/discharge station with battery management suitable for use with
all current battery types. With integral equalizer for six-cell,
Lithium- Polymer (LiPo), Lithium-Ferrum (LiFe) and Lithium-Ion (LiIon)
batteries. Maximum 10A charge current; maximum 80W charge power; can be
powered by a 12 Volt car battery or from 100V-240V via the built in
switch-mode power supply.
Optimized Operating Software
SKYRC 6x80 Plus features the so-called AUTO function that set the
feeding current during the process of charging or discharging.
Especially for lithium batteries, it can prevent the overcharging which
may lead to an explosion due to the user's fault. It can disconnect the
circuit automatically and alarm once detecting any malfunction. All the
programs of this product were controlled through two way linkage and
communication, to achieve the maximum safety and minimize the trouble.
All the settings can be configured by users!
Internal Independent Lithium Battery Balancer
SKYRC 6x80 Plus employs an individual-cell-voltage balancer. It isn't
necessary to connect an external balancer for balance charging.
Balancing Individual Cells Battery Discharging
During the process of discharging, SKYRC 6x80 Plus can monitor and
balance each cell of the battery individually. Error message will be
indicated and the process will be ended automatically if the voltage of
any single one cell is abnormal.
Adaptable to Various Type of Lithium Battery
SKYRC 6x80 Plus is adaptable to various types of lithium batteries, such as LiPo, LiIon and the new LiFe series of batteries.
Fast and Storage Mode of Lithium Battery
Purposes to charge lithium battery varies, 'fast' charge reduce the
duration of charging, whereas 'store' state can control the final
voltage of your battery, so as to store for a long time and protect
useful time of the battery.
1 to 5 cyclic and continuous process of charge>discharge or
discharge > charge is operable for battery refreshing and balancing
to stimulate the battery's activity.
The charger can store up to 10 different charge/discharge profiles for
your convenience. You can keep the data pertaining to program setting of
the battery of continuous charging or discharging. Users can call out
these data at any time without any special program setting.
Terminal Voltage Control(TVC)
The charger allows user to change the end voltage.
Lipo Battery Meter
The user can check battery's total voltage, the highest voltage, the lowest voltage and each cell's voltage.
Motor RPM Tester
Users connect the sensor motor and charger with sensor wire, set the pulse width and test the RPM of the motor.
Connect the servo and the charger with wire, change the pulse width value and check whether the servo works or not.
Re-Peak Mode of NiMH/NiCd Battery
In re-peak charge mode, the charger can peak charge the battery once,
twice or three times in a row automatically. This is good for making
certain the battery is fully charged, and for checking how well the
battery receives fast charges.
Delta-peak Sensitivity for NiMH/NiCd
Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge
termination program based on the principle of the Delta-peak voltage
detection. When the battery's voltage exceeds the threshold, the process
will be terminated automatically.
Automatic Charging Current Limit
You can set up the upper limit of the charging current when charging
your NiMH or NiCd battery, it is useful for the NiMH battery of low
impedance and capacity in the 'AUTO' charging mode.
The charging capacity is always calculated as the charging current
multiplied by time. If the charging capacity exceeds the limit, the
process will be terminated automatically when you set the maximum value.
The battery's internal chemical reaction will cause the temperature of
the battery to rise. If the temperature limit is reached, the process
will be terminated.
Processing Time Limit:
You can also limit the maximum process time to avoid any possible defect.
PC Control Software “Charge Master”
The free “Charge Master” software gives you unparalleled ability to
operate the charger through the computer. You can monitor pack voltage,
cell voltage and other data during the charging, view charge date in
real-time graphs. And you can initiate, control charging and update
firmware from “Charge Master”. (This unit is not the bluetooth version)